Nacecare-solutions TTV5565 Instrukcja Użytkownika

Owner InstructionsOriginal InstructionsWarning! Read instructions before using the machineTTV - 5565 / 200TScrubber Dryer - Operator Instructor Manual

10Featuring the new OBS (Octagonal Brush System); The brushes simply push-t up onto the chucks making tting and removal a simple process.Ensure the

11The TTV-5565 is equipped with a large capacity 22.5 gall clean-water tank allowing, for large areas to be covered in a single ll.To ll the clean-w

12When handling and mixing chemicals.Always ensure that chemical manufacturers safety guidelines are followed.Only use chemicals recommended for use i

13Fig.20Fig.22After preparing the oor (see previous section), we are now ready to set the controls to suit the cleaning conditions.Before any setting

14Set automatic Chemical Dosing Mix as required, depending on oor type and level of soiling.Set desired traction Speed as required, depending on oor

15Fig.24Fig.24 aNOTE: It is recommended this option is NOT used all the time and is for spot cleaning only.The run-time of the machine may decrease if

16Breakaway oor-toolFig.26The oor-tool design incorporates a breakaway feature.Allowing it to safely disengage from its mounting should it become ca

17Fig.30The optional off-aisle cleaning kit gives added exibility to the operator. The kit can be used to clean hard to reach / inaccessible areas. R

18Next remove oor-tool vacuum hose and ush out with clean water.Next empty clean-water tank, using emptying hoseand again ush out with clean water.

19! !ALWAYS ENSURE THAT THE BATTERY IS DISCONNECTED PRIOR TO ANY MAINTENANCENote:Floor Tool adjusters are factory set for optimal performance.The blad

2IndexPage 2Machine overviewPage 3Control panel overviewPage 4Rating label / Personal Protective Equipment / SpecicationsPage 5Safety PrecautionsPage

20The battery meter displays the charge level of the batteries; when fully charged, all meter lights are illuminated.As the machine is used and the ba

21ALWAYS ENSURE THAT THE MACHINE IS ON LEVELGROUND BEFORE DISENGAGING BRAKE ARM.NEVER DISENGAGE THE BRAKE WHEN THE MACHINEIS ON A SLOPE / GRADIENT.!!

22Green Status Indicator Fault Possible Cause Effect on Product Investigate the Following Action Required If fault persists1 Flash with pause Batteri

23LCD Display Fault Possible Cause Effect on Product Investigate the Following Action Required If Fault PersistsBlank * No power * Key switched off* E

24Failure to rectify the problem or in the event of a breakdown contact your Nacecare dealer or the Nacecare Technical helpline +44 (0) 900 1 905

25606253 HD Nyloscrub (2 req) 13 inch (STANDARD) 606252 HD Nyloscrub (2 req) 11 inch (STANDARD)606174 Polyscrub (2 req) 13 inch 60617

26TTV 5565 Variable Speed - 50% ow rateDRW - 15818 (A01) 24/02/14

27

235672 04/14 (A19)This machine has been packed with the following:Charging LeadFusesIsolator Key / PinHose Hook38 / 32mm AdaptorSignedTTV 5565This Pro

3 1. Operator control panel ( see page 4 ) 2. Charger inhibit lead 3. Clean-water tank ll point 4. Floor-tool raise / lower lever 5. Clean-wat

423456781011912Control Panel OverviewFor full easy to follow instructions on control panel set up and use, see machine operation page 14.1311 Variable

5Machine DescriptionCompany name and addressVoltage FrequencyWeightMachine yr/ wk / serial numberNoise LevelHand Arm VibrationMax GradientAbout the Ma

6Component Interval Inspect forBrushes DAILY Bristle damage, wear, drive collar wearSqueegee Blade BEFORE EACH USE Wear, cracks, splitsFilters BEFORE

7Only use brushes provided with the appliance or those specied in the instruction manual. The use of other brushes may impair safety. A full range of

8Please read before commencing any operation.After the removal of all the packaging, carefully open and check the contents of the start up pack (Fig.1

9ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF BEFORE MAKING ANY ADJUSTMENTS!!Lower the oor-tool arm by moving the release lever to the lower positi